TM 9-2320-211-20
(3) Remove the capscrew (9) and safety nut
starter cable to the terminal stud on top of the
clamping the bracket (10) to the starter (12).
solenoid, and remove the cable from the terminal
stud.
Spread the bracket, and slide the bracket with the
(2) Remove the nut and washer securing the
bellcrank and control link over the end of the
starter.
starter primary cable to the upper terminal stud on
the left side of the solenoid, and remove the wire
(4) Remove the cotter pin securing the front
from the terminal stud.
end of the control link to the bellcrank, and remove
the line from the bellcrank.
(3) Remove the nut and washer securing the
(5) Remove the c o t t e r p i n a n d w a s h e r
battery cable to the terminal stud on the bottom of
the solenoid, and remove the cable from the ter-
s e c u r i n g the bellcrank to the bracket (10), and
minal stud.
remove the bellcrank from the bracket.
( 4 ) Remove the four capscrews and safety
(6) Remove the two screws and nuts securing
nuts securing the solenoid to the inside of the frame
the control rod mounting plate to the underside of
right side rail, and remove the solenoid from the
t h e toeboard. Remove the mounting plate and
side rail.
control rod (5) from the toeboard.
b. Installation.
b. Installation of Solenoid (fig. 2-25).
(1) Position the control rod mounting plate
(1) Position the starter solenoid on the inside
of the frame right side rail, and secure it with four
and control rod (5) on the underside of the
toeboard, and secure them with two screws and
capscrews and safety nuts.
(2) Install the battery cable on the terminal
nuts.
(2) Position the bellcrank (11) on the pin at
stud at the bottom of the solenoid, and secure it
with a washer and nut.
the upper end of the bracket (10), and secure it
with a washer and cotter pin.
(3) Install the primary cable on the upper
terminal stud at the left side of the solenoid, and
(3) Insert one end of the control link (7) in the
hole in the lower end of the bellcrank, and secure it
secure it with a washer and nut.
with a cotter pin.
(4) Install the starter cable on the terminal
( 4 ) Slide the bracket (10), bellcrank, and
stud at the top of the solenoid, and secure it with a
control link on the starter (12), and loosely clamp
washer and nut.
the bracket to the starter with a screw (9) and nut.
c. Removal of Manual Starter Switch (fig. 2-
(5) While sliding the bracket on the starter,
150).
aline the bellcrank and yoke at the lower end of the
(1) Remove the two electrical leads from the
control rod (5), and tighten the screw and nut to
starter switch mounted on the starter.
(2) Remove the set screw.
clamp the bracket to the starter.
(6) Position the control rod yoke on the
(3) Unscrew the starter switch (4) from the
bellcrank, and secure it with the yoke pin and a
starter.
d. Installation of Manual Starter Sw itch (fig. 2-
cotter pin.
150). Install the starter switch in the reverse order
(7) Insert the rear end of the starter control
of removal.
link in the hole in the upper end of the lever (8),
and secure it with a cotter pin.
a. Removal of Solenoid (fig. 2-25).
(1) Remove the nut and washer securing the
Section XIX. MAINTENANCE OF STARTING SYSTEM--
D I E S E L AND MULTIFUEL
2-128. Starter
2-127. General
The starting system components discussed in this
a. Removal.
section are the starter and solenoid.
(1) Remove the nuts and lockwashers
securing the three cables to the starter and starter
solenoid.
