TM 9-2320-260-34-1
8-6. TRANSMISSION MAINTENANCE
THIS TASK COVERS:
c . Assembly
a. Disassembly
b. Cleaning and Inspection
INITIAL SETUP
MATERIALS/PARTS (Contd)
APPLICABLE MODELS
Gasket (Appendix D, Item 134)
All
Gasket (Appendix D, Item 130)
TOOLS
Gasket (Appendix D, Item 155)
General mechanic's tool kit
Two gaskets (Appendix D, Item 131)
(Appendix B, Item 1)
Gasket (Appendix D, Item 133)
Mechanical puller (Appendix B, Item 14)
Gasket (Appendix D, Item 135)
Torque wrench, 3/4-in. dr.
Gasket (Appendix D, Item 136)
(Appendix B, Item 2)
Gasket (Appendix D, Item 138)
2-318-in. socket, 1-in. dr.
Five setscrews (Appendix D, Item 487)
(Appendix B, Item 18)
Two cotter pins (Appendix D, Item 23)
314-in. to 1-in. adapter
Seal (Appendix D, Item 420)
(Appendix B, Item 19)
Seal (Appendix D, Item 428)
2-1/8-in. socket, 1-in. dr.
Seal (Appendix D, Item 430)
(Appendix B, Item 20)
Four woodruff keys (Appendix D, Item 548)
Companion flange replacer
Woodruff key (Appendix D, Item 546)
(Appendix B, Item 96)
Three expansion plugs (Appendix D, Item 323)
Inside micrometer (Appendix B, Item 9)
Locknut (Appendix D, Item 166)
Outside micrometer (Appendix B, Item 8)
Snapring (Appendix D, Item 513)
Arbor press (Appendix B, Item 7)
Snapring (Appendix D, Item 514)
Lifting device
Snapring (Appendix D, Item 515)
Rope sling
Snapring (Appendix D, Item 516)
Snapring (Appendix D, Item 517)
MATERIALS/PARTS
GAA grease (Appendix C, Item 14)
Thirteen lockwashers
Sealing compound (Appendix C, Item 43)
(Appendix D, Item 219)
Two puller screws (Appendix C, Item 38)
Nine lockwashers (Appendix D, Item 223)
Eight lockwashers (Appendix D, Item 217)
REFERENCES (TM)
Six lockwashers (vehicles with PTO)
LO 9-2320-260-12
(Appendix D, Item 215)
TM 9-2320-260-34P-1
Four lockwashers (Appendix D, Item 227)
EQUIPMENT CONDITION
Twelve screw-assembled lockwashers
(all vehicles except M816)
Transmission drained (LO 9-2320-260-12).
(Appendix D, Item 385)
Transmission removed (para. 8-4).
Ten screw-assembled lockwashers (M816)
GENERAL SAFETY INSTRUCTIONS
(Appendix D, Item 385)
All personnel must stand clear during lifting
Six screw-assembled lockwashers
operations.
(Appendix D, Item 389)
Six screw-assembled lockwashers
(Appendix D, Item 387)
a. Disassembly
1. Remove four screws (1), lockwashers (2), two spring clips (5), and pads (29) from clutch release
sleeve (28). Discard lockwashers (2).
2. Remove clutch release sleeve (28) from input shaft (9).
3. Remove grease fitting (26) and bearing (27) from clutch release sleeve (28).
4. Remove two screws (24), lockwashers (23), and spacers (22) from clutch release yoke (25). Discard
lockwashers (23).
