TM 9-2320-260-20
I
THIS TASK COVERS:
a. Removal
b. Installation
INITIAL SETUP
APPLICABLE MODELS
EQUIPMENT CONDITION
Exhaust pipe removed (para. 3-40).
All
q Front composite light assembly removed
MATERIALS/PARTS
Twenty-two locknuts
Two lockwashers
q Power steering assist cylinder front and side
REFERENCES (TM]
shields removed (para. 11-26).
TM 9-2320-260-20P
1.
Remove locknut (7), harness clamp (6), and screw (5) from fender (1). Discard locknut (7).
2.
Remove locknut (8), harness clamp (9), lockwasher (10), screw (13), lockwasher (10), terminal (12),
harness clamp (14), and harness (15) from fender (1) and brace (11). Discard locknut (8) and
lockwashers ( 10).
3.
Remove six locknuts (4), washers (3), screws (2), and washers (3) from fender support (16) and
fender (1). Discard locknuts (4).
4.
Remove two locknuts (17), washers (18), screws (21), and washers (20) from headlight bracket (24)
and fender (1). Discard locknuts (17).
Remove two locknuts (19), screws (23), washers (22), and headlight bracket (24) from fender (1).
5.
Discard locknuts (19).
Turn four fasteners (32) counterclockwise and remove access panel (31) from fender (1).
6.
Remove three locknuts (36), screws (40), washers (39), plate (37), and shield (38) from fender (1).
7.
Discard locknuts (36).
Remove four locknuts (33), washers (34), screws (41), and washers (34) from fender (1) and rear
8.
brace (35). Discard locknuts (33).
9.
Remove three locknuts (25), washers (26), screws (30), washers (26), fender (1), and fender
anti-squeak (28) from front brace (27). Discard locknuts (25).
Remove grommet (29) from fender (1).
10.
1.
Install grommet (29) on fender (1).
2.
Install fender anti-squeak (28) and fender (1) on front brace (27) with three washers (26),
screws (30), washers (26), and new locknuts (25).
3.
Secure fender (1) to rear brace (35) with four washers (34), screws (41), washers (34), and new
locknuts (33).
4.
Install shield (38) on fender (1) with three washers (39), screws (40), plate (37), and three new
locknuts (36).
5.
Install access panel (31) on fender (1) with four fasteners (32).
6.
Install headlight bracket (24) on fender (1) with two washers (22), screws (23), and new
locknuts (19).
7.
Secure headlight bracket (24) to fender (1) with two washers (20), screws (21), washers (18), and
new locknuts (17).
8.
Secure fender (1) to fender support (16) with six washers (3), screws (2), washers (3), and new
locknuts (4).
Install harness (15) on fender (1) and brace (11) with harness clamp (14), terminal (12),
9.
new lockwasher (10), screw ( 13), new lockwasher ( 10), harness clamp (9), and new locknut (8).
10.
Install harness clamp (6) on fender (1) with screw (5) and new locknut (7).
11-18
