LO 9-2350-247-12
LUBRICATION ORDER
(Supersedes LO 9-2350-247-12, March 1962)
8 JULY 1994
KEY
EXPECTED
TEMPERATURES*
REFILL
INTERVALS
CAPACITY
+40F
0F
Above
to
to
(APPROX)
32F
-10F -65F
4 qt.
OE/
OEA
D - Daily
OE/HDO (MIL-L-2104C) LUBRICATING OIL,
OE/
HDO-30 HDO-10
OR OEA (MIL-L-46167) INTERNAL COMBUSTION
S - Every 200 hours
ENGINE
on generator ETl
Generator
meter (see TM
Speed Increaser
9-2350-247-10)
Gear Assembly
or semi-annually
For Arctic Operation Refer to FM 9-207
NOTES
2. GENERATOR SPEED INCREASER GEAR AS-
1. GENERATOR SPEED INCREASER GEAR AS-
SEMBLY FILTER. Every 200 hours on generator ETI
SEMBLY. Daily check generator speed increaser gear
meter (TM 9-2350-247-10) or semi-annually
assembly oil level for between ADD and FULL marks
during oil change, replace filter element. Remove
on gauge rod. Add oil (OE/HDO) through dipstick tube
locking wire, cover, filter element, and two preformed
as necessary. Every 200 hours on generator ETI
packings (see M1015A1 portion of TM 9-2350-247-
meter (TM-2350-247-10) or semi-annually drain
20). Dscard locking wire, element, and packings.
generator speed increaser gear assembly oil. To drain,
Clean inside of cover with dry cleaning solvent (PD-
remove hull bottom access cover (TM 9-2350-247-20)
680, type III) and install two new packings and new
and speed increaser drain plug. Inspect oil being
element. Install filter cover and new locking wire. After
drained for metallic particles. If metal chips are found
filling generator speed increaser gear assembly (see
in oil, notify your supervisor. Clean and install drain
Note 1), check for oil leaks with engine operating.
pIug. Service oil filter and breather (see Notes 2 and 3).
To fill, remove plug with preformed packing and add oil
3. GENERATOR SPEED INCREASER GEAR AS-
(OE-HDO) (refill capacity about 4 quarts) to bring level
SEMBLY BREATHER. Every 200 hours on generator
between ADD and FULL marks on gauge rod. Discard
ETI meter (TM 9-2350-247-10) or semi-annually, dur-
packing. Clean fill plug, apply coat of antiseize com-
ing oil change, clean breather. Remove breather,
pound to plug threads, position new preformed pack-
clean with dry cleaning solvent (PD-680, type Ill),
mg on Iu and install plug. Run carrier en ine and
apply coat of sealing compound to breather threads,
check for leaks at filter and at drain plug. INSTALL
and install breather.
BOTTOM ACCESS COVER SECURELY.
WARNING
NOTE
Dry cleaning solvent PD-680 is toxic and flam-
mable. Death or injury may result. Always use in
If M1015A1 carrier has a shelter on it, it may be
an open area with good air flow, away from sparks,
necessary (depending on the type of shelter) to
heat, or flames. Wear protective goggles and
slide shelter back on skid guides for access to
gloves. Do not breathe vapors. Avoid contact with
some lubrication points (see M1015A1 portion of
TM 9-2350-247-10.
skin, eyes, and clothes. If you get dizzy while using
solvent, breathe fresh air and get medical help.If
solvent gets on hands, wash them. If solvent gets
in eyes, flush eyes with fresh water and get medi-
cal help immediately. Keep fire extinguisher
nearby.
Use sealing compound 8030-00-543-4384 antiseize compound - 8030-00-286-5453, or Permalex - 5330-00-252-3391.
Card 33 of 40
