TM 9-2320-211-34P
this column in lieu of a quantity indicates that a
(3) Recoverability Code, indicates whether
unserviceable items should be returned for recovery
definite quantity cannot be indicated (e.g., shims,
spacers, etc.).
or salvage, Recoverability Codes are--
f. 30-Day DS/GS Maintenance Authorization,
Code
Explanation
Columns 6, and 7.
R
Applied to repair parts, (assemblies and compo-
(1) The Repair Parts List includes asterisk
nents) special tools and test equipment which are
considered economically reparable at Direct and
entries in separate columns--one for Direct
General Support Maintenance levels. When the
Support (DS) and one for General Support (GS)--
item is no longer economically reparable, it is
as appropriate to indicate the total range of repair
normally disposed of at the GS level. When supply
parts authorized for usc at that category or required
considerations dictate, some of these repair parts
to be removed or disassembled during the per-
may be listed for automatic return to supply for
depot level repair as set forth in AR 710-50. When
form ante of authorized maintenance operations.
so listed, they will be replaced by supply on an
They will be requisitioned initially on an "as
exchange basis.
required" basis. The repair parts authorized at the
S
Repair Parts, Special Tools, Test Equipment and
DS/GS levels will be those authorized for the
assemblies which are economically reparable at
maintenance mission at these levels. Requirements
DSU and GSU activities and which normally are
for repair part stockage and for distribution to
furnished by supply on an exchange basis. When
items are determined by a GSU to be
supported units will be based on demand and
uneconomically reparable, they will be evacuated
determined in accordance with AR 710-2.
to a depot for evaluation and analysis before final
(2) Special Tools or Teat, Measurement and
disposition.
Diagnostic Equipment (TMDE) and other support
T
Higher dollar value recoverable repair parts,
equipment peculiar to an item are listed with
special tools, and teat equipment which are subject
quantities in the appropriate density--spread--
to special handling and are issued on an exchange
basis. Such items will be evacuated to the depot
allow ante columns.
for overhaul or final disposition. Communications-
g. 1 - Y e a r A l l o w a n c e s P e r 1 0 0 E q u i p .
Electronics and Missle Support items will be
ments/Contingency Planning Purposes, Column
repaired / overhauled only at depots.
8. This column indicates, opposite each item, the
U
Repair Parts, Special Tools and Test Equipment
quantity required for distribution and contingency
specifically selected for salvage by reclamation
planning purposes. The range of items indicates
units because of precious metal content, critical
materials, high dollar value or reusable casings or
total quantities of all authorized items required to
castings.
provide for adequate support of 100 equipments for
one year.
NOTE
h. Depot Maintenance Allowance Per 100
When no code is indicated in the
Equipments, Column 9. This column indicates
recoverability column, the part will be
opposite each item, the quantity authorized for
considered non-recoverable.
depot maintenance of 100 equipments. Items
b. Federal Stock Number (FSN, Column
authorized for use as required but not for initial
2. This column indicates the Federal stock number
stockage are identified with an asterisk in the
a s s i g n e d to the item and will be used for
allowance column.
requisitioning purposes.
i. Illustration, Column 10. This column is
c. Description, C o l u m n 3. This column in-
divided as follows:
dicates the Federal item name and any additional
(1) Figure Number, Column 10a. Indicates
description of the item required, A part number or
the figure number of illustration in which the item
other reference number is followed by the ap-
is shown.
p l i c a b l e five-digit Federal supply code for
(2) Item Number, Column 10b. Indicates the
manufacturers in parentheses. Repair parts
callout number used to reference the item in the
quantities included in the kits, sets, within one
illustration.
functional group are shown in front of the repair
part name. Material required for manufacture or
1-4. Special Information
fabrication is identified.
a. Identifications of the usable on codes included
d. Unit of Measure (U/M), Column 4. A 2
in column 3 of this publication are--
character alphabetic abbreviation indicating the
Used on
Code
amount or quantity of the item, upon which the
All Models
A
allowances are based, e.g., ft., ea., pr., etc.
Vehicles with R6602 Gas Engine
AA
e. Quantity Incorporated in Unit, Column
Vehicles with LDS-465-1A multifuel engines
AB
5. This column indicates the quantity of the item
Vehicles with ENDT 673 Mack Diesel Engines
AC
used in the Assembly Group. A "V" appearing in
1-2
